Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
OpenWrt for new hardware
#38
hmm. So the new units have a known flaw which I corrected with the latest available firmware, and even made the ports jibe with the labels.

Can you confirm that you upgraded to the very newest firmware? It has never exhibited any issue of not saving configs to flash.

Process to be sure you do not have old configs.

Power off. Wait a second or 2 then power on, and hold in the reset switch. You will see all of the lights flash. After the 3rd flash release the switch. If you have a ping going to 192.168.1.1 you will see that it begins to ping soon after. Once it pings, point your browser to 192.168.1.1 and you will get the recovery screen. Choose the new firmware and then apply it. It will be doing the reflash with n o feedback. After about 5 seconds close your browser, but do NOT touch the power to the unit. It has to complete.

When it begins to ping again, you can go to the unit and begin to configure. I usually just enter the password and save. Then I log out and log back in to check the password. If that passes, pull the power plug and try a full power cycle. It should require the new password if it was save to flash.

Please let me know what it does.
Reply


Messages In This Thread
OpenWrt for new hardware - by lonnie - 01-06-2020, 04:39 PM
RE: OpenWrt for new hardware - by lonnie - 01-10-2020, 04:48 AM
RE: OpenWrt for new hardware - by TalStar - 01-22-2020, 08:27 PM
RE: OpenWrt for new hardware - by TalStar - 01-28-2020, 07:55 PM
RE: OpenWrt for new hardware - by lonnie - 02-02-2020, 04:33 PM
RE: OpenWrt for new hardware - by TalStar - 02-04-2020, 07:05 PM
RE: OpenWrt for new hardware - by lonnie - 02-07-2020, 03:23 PM
RE: OpenWrt for new hardware - by go.fast - 02-07-2020, 09:30 PM
RE: OpenWrt for new hardware - by lonnie - 02-08-2020, 06:11 PM
RE: OpenWrt for new hardware - by go.fast - 02-09-2020, 01:39 AM
RE: OpenWrt for new hardware - by TalStar - 02-15-2020, 04:54 PM
RE: OpenWrt for new hardware - by lonnie - 02-16-2020, 11:29 PM
RE: OpenWrt for new hardware - by lonnie - 02-17-2020, 06:06 AM
RE: OpenWrt for new hardware - by go.fast - 02-18-2020, 04:58 AM
RE: OpenWrt for new hardware - by lonnie - 02-18-2020, 03:44 PM
RE: OpenWrt for new hardware - by TalStar - 02-19-2020, 12:12 AM
RE: OpenWrt for new hardware - by lonnie - 02-19-2020, 06:13 PM
RE: OpenWrt for new hardware - by TalStar - 02-19-2020, 11:18 PM
RE: OpenWrt for new hardware - by lonnie - 02-20-2020, 04:42 PM
RE: OpenWrt for new hardware - by TalStar - 02-25-2020, 06:13 PM
RE: OpenWrt for new hardware - by lonnie - 02-26-2020, 04:17 PM
RE: OpenWrt for new hardware - by TalStar - 02-26-2020, 09:50 PM
RE: OpenWrt for new hardware - by lonnie - 02-27-2020, 02:25 AM
RE: OpenWrt for new hardware - by lonnie - 02-27-2020, 07:55 PM
RE: OpenWrt for new hardware - by lonnie - 03-04-2020, 04:14 PM
RE: OpenWrt for new hardware - by TalStar - 03-04-2020, 09:39 PM
RE: OpenWrt for new hardware - by lonnie - 03-05-2020, 03:11 PM
RE: OpenWrt for new hardware - by lonnie - 03-05-2020, 04:19 PM
RE: OpenWrt for new hardware - by TalStar - 03-05-2020, 09:08 PM
RE: OpenWrt for new hardware - by lonnie - 03-06-2020, 04:00 PM
RE: OpenWrt for new hardware - by lonnie - 03-09-2020, 10:31 PM
RE: OpenWrt for new hardware - by TalStar - 05-06-2020, 05:13 PM
RE: OpenWrt for new hardware - by lonnie - 05-07-2020, 04:11 PM
RE: OpenWrt for new hardware - by lonnie - 05-08-2020, 12:07 PM
RE: OpenWrt for new hardware - by lonnie - 05-09-2020, 06:36 PM
RE: OpenWrt for new hardware - by lonnie - 05-12-2020, 01:49 AM
RE: OpenWrt for new hardware - by TalStar - 05-19-2020, 04:29 AM
RE: OpenWrt for new hardware - by lonnie - 05-19-2020, 02:39 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)